Xantrex MS2000 Manual de usuario Pagina 42
- Pagina / 126
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation
2–12 975-0125-02-01
Operating in Invert Mode
Once the inverter/charger is installed, you can operate it in invert mode.
To operate in invert mode from the front panel:
1. Press the Inverter Enable button on the MS2000.
2. If external AC is present, the External AC light illuminates. If AC is present
and you want to run the inverter, remove AC so the inverter turns on.
Once the Inverter On light is on, the MS2000 inverter is ready to deliver AC
power to the loads.
◆ To operate the inverter with the System Control Panel, refer to Chapter 3,
“Configuration”.
Load Sense Mode
The Load Sense mode of the MS2000 reduces battery power consumption in order
to conserve battery charge.
When the inverter is enabled, the inverter/charger can be configured to search for
an acceptable AC load. (It does this when you enable (turn on) “Load Sense” on
the MS2000 Advanced Menu on the System Control Panel and set the load sense
power threshold “Sense Below.”)
When the load sense feature is disabled (turned off), the inverter is continuously
on. With load sense enabled, the inverter output consists of pulses if the unit
doesn’t detect a load that meets the load sense parameters. When an acceptable
load is detected, the inverter output is turned on automatically and provides full
output power.
WARNING
Review the “Important Safety Instructions” on page vii before operating the
inverter/charger.
Important:
If you are having problems with any of your loads, refer to
“Inverter Applications” on page 4–15.
- Operation Guide 1
- About This Guide 5
- Conventions Used 6
- Symbols Used 6
- Related Information 7
- Contact Information 7
- Important Safety Instructions 9
- Explosive Gas Precautions 11
- FCC Information to the User 12
- Contents 13
- Configuration 14
- Troubleshooting 15
- 975-0125-02-01 xv 17
- Introduction 19
- Premium Power and Ease of Use 20
- How MS2000 Works 21
- 1–4 975-0125-02-01 22
- Xanbus System 23
- Xanbus Enabled 23
- MS2000 Features 25
- Figure 1-3 26
- Table 1-2 26
- Side Panel Features 27
- CAUTION: Equipment Damage 27
- Figure 1-5 28
- DC Grounding Completed 28
- DC Terminal Covers 29
- Battery Temperature Sensor 29
- Operation 31
- Important: 32
- On Start Up 34
- Power On Reset 34
- System Start-up Check 35
- System Modes 36
- Operate Mode 37
- Power Save Mode 37
- Safe Mode 38
- CAUTION: Unexpected behavior 38
- 975-0125-02-01 2–9 39
- Hibernate mode 40
- 975-0125-02-01 2–11 41
- Operating in Invert Mode 42
- Power Output 43
- Operating in Charger Mode 44
- Echo Charger Operation 45
- 2–16 975-0125-02-01 46
- WARNING: Explosive gases 48
- Equalizing Batteries 49
- Power Share 52
- Faults and Warnings 54
- System Control 56
- System Menu Map 57
- Viewing the System Screen 58
- 975-0125-02-01 3–5 59
- MS2000 Configuration Menus 60
- 975-0125-02-01 3–7 61
- MS2000 Device Menu 62
- AC Input 63
- Echo Chg Out 63
- MS2000 Menu (Basic) 64
- Equalize 66
- 975-0125-02-01 3–13 67
- 3–14 975-0125-02-01 68
- Batt Type 69
- Batt Size 69
- Clear Faults 70
- MS2000 Menu (Advanced) 71
- Max Chg Rate 72
- Echo Chg 72
- Load Sense 73
- View Device Info 73
- Basic Menu 73
- 975-0125-02-01 3–21 75
- Sub-Menus 76
- Sense Interval 77
- # Chg Stages 77
- Eqz Volts 78
- Force Charge 78
- Lo AC Volt 79
- Lo AC Freq 79
- Hi AC Volt 80
- Hi AC Freq 80
- View Fault Log 81
- View Warning Log 81
- View Event Log 81
- Restore Defaults 82
- Warning Types 85
- Troubleshooting Reference 86
- 975-0125-02-01 4–5 87
- Warning Messages 88
- Table 4-3 89
- Fault Messages 91
- Table 4-4 92
- Inverter Applications 97
- Searching 98
- Specifications 99
- Inverter Specifications 100
- Main Charger Specifications 101
- Echo Charger Specifications 102
- Environmental Specifications 103
- Regulatory Approvals 103
- Fan Operation 103
- Charger Mode 104
- Reference for the Main 105
- Battery Charging 105
- Charge Algorithm Stages 106
- Bulk Charge 107
- Absorption Charge 107
- Float Charge 107
- Two-Stage Charging 108
- Charge Algorithm Graph 109
- Charge Algorithm Definitions 109
- AC Reconnect Summary 110
- Terminology 111
- Glossary 112
- Abbreviations 115
- Warranty 117
- Disclaimer 118
- Return Procedure 119
- Out of Warranty Service 119
- Information About Your System 120
- Xantrex Technology Inc 126
Relacionado con productos y manuales para Adaptadores E Inversores De Energía Xantrex MS2000
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales